Cloud Sprinkler Manual

• Select Program by using or key, then press
• PUMP/ MASTER
  • Select pump/ master valve number using or key.
• MODE
  • Select zone run mode with Normal or Cycle by using or key.
  • If you have selected the Cycle mode, set the number of cycles and the delay between cycles on the next menu-manual by pressing th key.
• START TIME
  • Set up to 4 start times. Use the and keys to increment or decrement the digit. Use the and keys to change the digit to the next or previous one. To disable the start time, increment or decrement the hour digit until "Disabled" is shown on the corresponding start time position.
• DAYS
  • Select master days with a two-week calendar. Use the first letter of the weekday to represent it (e.g., "S" for Sunday). Enable or disable a day using the or keys. Use the or keys to change the days. You can also set the day type to All, Odd, or Even when the cursor is at the day option.
• OPTION
  • There are two options that can be selected here: Water Option and Auto Weather option. Change the option value by pressing the or key. To change the option to Auto Weather, use the or key.
• ZONE WATER
  • Up to 24 zones run time can be set here. Maximum zone run time hour is 12. Use or keys for increment or decrement digit and use or keys for change digit.

• Display status of the program. Change program by press or key.

• Select program
  • Change program by press or key.
• Set % Program
  • Set program percentage for each month. Change percentage by press or keys and change months using or

• Program can be disabled permanently or particular period in hours. Disable program by press or keys and change program by or keys. Select 0 Hour for set permanently or select desired delay.

• To clear the program, including start time and zone times, press the or key to change the program. Press the key to clear. A confirmation menu-manual will appear; press to clear or press the key to go back to the previous menu-manual without clearing the program.

• This log is only for displaying the program's last start and stop information. The entire system log is available in different menu-manuals under INFORMATION. Change the program by pressing the or key.

Program schedule and zones can be run manually. Use the or keys to select either Program or Zone.

For the program, select the program number by pressing the or keys. Press the next step to enter the program percentage by pressing the key. Once a suitable percentage is selected by using or key, press the key to start the program manually. Make sure there is a valid time or volume set for the program zones to run.

For manual zone run, select zones from start to end. Then, set the hours and minutes. There is an option to select the pump as well. To change parameters, use the or keys, and to set values, use the or keys.

• Wi-Fi is compatible only with 2.4 GHz networks.

  Select Wi-Fi Status or Setup by using or key, then press key

  The Wi-Fi status shows the MAC address, IP address, and signal strength

  Configure Wi-Fi using either a phone or the keypad. These options can be selected by or key, then press key

  ---

  Wi-Fi configuration By Phone:

  1. Enable Wi-Fi setup in Cloud Sprinkler by navigate to Settings>Wi-Fi Setup>By Phone option. For security reasons, this feature is automatically disabled either after 3 minutes or upon connecting to the internet.
  2. Open your phone's Wi-Fi settings.
  3. Select the network "Cloud Sprinkler".
  4. Enter the password: "password".

     Note: There is a chance of disconnection and reconnection to the existing Wi-Fi network due to no internet connection. Continuously monitor the Wi-Fi connection to Cloud Sprinkler.

  5. Open your browser and go to: 192.168.10.1.
  6. Follow the instructions on the page.

  Once you have completed the steps, your Cloud Sprinkler will be connected to your Wi-Fi network.

  ---

  Wi-Fi configuration By Keypad:

  Enable Wi-Fi setup in Cloud Sprinkler by navigate to Settings>Wi-Fi Setup>By Keypad option.

  The Wi-Fi will scan for the nearest Wi-Fi router and display available stations. Select the desired Wi-Fi station and press the key to enter the passkey.

  Passkey characters are grouped into three categories: alphabetic small letters, capital letters, numbers and symbols. These are selected by pressing the key. Each letter can be selected by pressing the or keys and then pressing the key. To move the cursor back, press the key. Once all the digits of the passkey are selected, keep pressing the or keys until the 'Set' text at the bottom of the display is selected, then press the key to set the passkey.

  ---

  Note: The Wi-Fi setup menu-manual option is not available on the app display section.

• View the QR code to add the device to your account. The device ID and model are embedded in the QR code. Use the mobile app camera to add the device to your account. Cloud Sprinkler™ can be added to only one account at a time; however, you can share the device at the app level with other people who use the AgroGlide™ app.

• Water meter inputs and Rain-Switch inputs can be configured as needed.

  Select the input type using the or key. Press the key to enter the setup.

  The water meter pulse rate can be selected using the or key. Use the or key to select the water meter number.

  For the rain switch, there is an option to select a closed or open contact type sensor. Use the or key to select different options such as sensor type, program numbers, and rain delay. Use the or key to change individual menu-manual values.

• Set time, date and time format in this section. Change individual digits with or keys and digit values with or keys. Press for validate time and date to system.

  There is an option to automatically set the time and date based on location at the app level.

• This feature is for direct-wired solenoids. The solenoid will rapidly switch on and off, approximately every second. This will create a clicking sound in every second, making it easy to locate the solenoid underground using a sound detector. Use or keys for change valve numbers. Press key to exit from Valve Find function.

  Warning: Do not connect the pump to the controller while using the Valve Find feature. It may damage the pump. The Valve Find feature automatically disables after 4 minutes.

• The embedded firmware can be updated through the internet. This section will check for updates and notify you if any are available. Press the key to update the firmware if an update is available. Automatically restart once finish updating.

  Warning: Do not power off the device while firmware updating.

• Up to the last 100 event logs with timestamps can be viewed. Use the or key to navigate to the next or previous event log.

• System fault. Use the or key to view more faults, if any.

• Output current is measured in milliamperes. This is very handy for troubleshooting field cable issues.

• Water meter readings are in liters. Use a direct-wired water meter for accurate flow measurements. Flow will not be accurate if you use a TW sensor. Use the or keys to change the water meter.

• VALVE/MASTER
  • Press key for see online AgroGlide™ AG-valves.
• WATER METER
  • Press key to see online AgroGlide™ AG-WaterMeter.

    or keys to change the AG-WaterMeter address.

• SWITCH
  • Press key to see online AgroGlide™ AG-Switch.

    or keys to change the AG-Switch address.

    Different kinds of AG-Switch functions can be configured through the app.

• MOISTURE
  • Press key to see online AgroGlide™ AG-Moisture/AG-Temperature sensor.

    or keys to change the AG-Moisture/AG-Temperature address.

• PRESSURE
  • Press key to see online AgroGlide™ AG-Pressure sensor.
• WATER LEVEL
  • Press key to see online AgroGlide™ AG-Level sensors.

    or keys to change the AG-Level address.

• About the Cloud Sprinkler™